Finally!!! the snow left us long enough for us to get in a very quickly prepared Work Session last weekend, April 23rd-24th…. but as I am writing this, snow is again falling… ever so lightly, but it is in the air… and the temps are back in the low 30’s. We knew we wouldn’t have a huge turnout simply because there wasn’t enough time for many of our volunteers to plan for it… AND… it was such a gorgeous day that many others were busy with yard cleanup and all of the accumulated Honey-Do’s on the perpetual list… understood!!!
We did have several of our Stalwarts make it to Corry for the couple of days, and for that we are grateful… Thanks to Grady, Steve and Bill for making the long treks… joining Norm, Tom and me in pulling more stuff apart and continuing with the creating and dimensioning of the new drawings. We certainly enjoyed their company and efforts… and managed to get quite a bit done. Thanks to Sandy and Ginny for keeping us all fed… “Job well done, Ladies!”
Norm and Grady checking out the Brass for wear and stamped numbers after removing the drive-line and pinions.
Steve sweeping up the rust and dirt after disassembling the arch-bar components.
Grady needle-scaling arch-bar parts.
The Trucks are now completely apart…. a bolt inventory and count for the Trucks has been taken, and now we are ready to begin cleaning those parts and repairing a couple of them that need some attention…. talk about rust and dirt… WOW… were those pieces stuck tight!!! A lot of pneumatic needle-scaling was done this weekend, the result being that all of those pieces are now ready for some serious grease and crud cleaning and sand blasting in preparation for a final inspection followed by primer and paint. Still more work to go, but it won’t be too long before the trucks begin going back together.
Grady inspecting the parts… a little bit smaller parts than the last Climax project.
Tom worked on refurbishing some pallets for moving parts and piled parts on them, ready for more cleaning.
Bill getting up close and personal with the two-speed fixed gears on the counter-shaft, which sits below the moveable gears on the crankshaft
Bill was busy on the lap-top adding more dimensions, and between the two of us we managed to make some headway in some of the wooden parts identification… some of Keith’s notes are visible on some of the pieces and others have his business cards rolled up and stuck in holes with further identification… then there were the pieces with no ID… it all comes down to good old logic, looking at some old photos when available, and a process of elimination…. slowly but surely we will get the picture of how it went together back in the day.
We picked up a vacuum for our sand blast cabinet, and managed to get all of the nuts and bolts in place, putting together the cabinet…. a bit more plumbing and procure a stock of sand and media and the Sand Blast cabinet for small parts will be ready to use.
Original roof bows and cab wall posts.
Roof supports of cab wall posts… with the water tank sitting behind.
Making sense of the pieces of the rear wall of the cab.
WORK SESSIONS:
We DO HAVE A DATE set for our next Work Session, and that will be on Saturday and Sunday morning, May 7th-8th. Continuing with cleaning, inspection and parts identification and sorting will be one of the tasks. Building of more Sawhorses will be happening as well. If our electrician is able to make it that weekend we will be continuing to extend our service lines in the building.
OPEN HOUSE:
We are always looking for more and new volunteers for Work Sessions… and we will need more volunteers to help out at our upcoming Open House… which will be on June 11th. Volunteers and relief-volunteers are needed for Information tables, signing in folks coming in the gate, selling memorabilia and tickets for raffles, and etcetera. So, drop me a note at corryrails@gmail.com to my attention… I’m Carl. Last year was a huge success but we didn’t have any extra volunteers… just barely enough… we all worked the whole day straight through… having twice as many volunteers would be wonderful… you don’t need to be an expert on any of this stuff… there is always someone around who can answer the tough questions. This year the Open House will be on the same Saturday as Corry-Fest (June 11th) which brings a lot of people home to Corry… It’s also Alumni Weekend… but there hasn’t been one for the last two years… so the town should be packed. There are a lot of folks who haven’t seen our project yet. We are also taking names of displayers and vendors for that Saturday.
NOVEMBER 2021 WORK SESSION – Finally Caught up on my Posts!!!
After our return from a successful trip to Alaska where we were able to retrieve some more of the missing locomotive parts and receive the original Builder Plate donated by the Andersen Family along with working on research, photos and video for our Documentary…. and then the move of the engines to Bill’s Machine Shop for evaluation and assembly, we were able to plan around everyone’s schedules and a case of Covid for one last end-of-the-year Work Session in November.
Thanks to a Mini-Grant from the Corry Community Foundation (Thank you, thank you, thank you!!!) we were able to add some much needed electrical expansion in our restoration building. This included an exterior light at the front door as well as one inside the front door, a run for an expansion Sub-Panel, several more breakers in the Main Panel and a run of conduit following the shelving on the west wall with several 4-way electrical outlets… YEA!!!! Progress is happening! We have been able to save some through additional material donations for beginning the expansion of electrical on the east side of the building next.
We had about 18 volunteers show up for the Saturday Session, including some new faces… welcome guys!!! They came not only from here in Corry, but from Clymer, Jamestown, Meadville, Columbus and Marietta, Ohio, Morgantown, WV and Virginia as well…. our fans and volunteers are not just local Corryites but truly National and International in scope… over the next couple of years we will see folks from all over showing up to be a part of this Build.
Some donated lumber was crafted into several stout saw-horses for use in our work on the frame… more will be built in the same manner in the future… it will take a bunch of them to support about 28 pieces of the frame floating a couple of feet off the floor (working height) during the cutting, drilling, mortise and tennoning, and multiple fittings of the new frame pieces in the near future.
Bill Simonton was up from Virginia to continue the work he is doing on the construction drawings for fabrication of the frame and the 3-D renditions of the locomotive… thanks Bill for all you do my friend.
Several worked on assembling of a newly donated sand-blast cabinet and a donated new portable engine hoist. Others, lead by Grady Smith, began the disassembly of the second geared truck. A handful came back on Sunday morning to finish up a few details… and then everyone headed home as reports were coming in of winds picking up and snow beginning to drop in mid-Ohio and central-PA.
One of the highlights of the weekend was the testing of our three steam whistles under air pressure… each had their own characteristics…. one was very deep in tone…. the 3-chime was the sweetest sound… and the original Climax Shop Whistle certainly got your attention… Walt Casler had said that in it’s day it could be heard in Spartansburg when it was blown… WOW!…. loud is the only word I have!!! and of course, ear protection was provided, since this was inside the building….lol!!!! Brad Minor from Clymer, NY did his magic on the whistles and came prepared to build a manifold off of our air tank…. thanks Brad!
Sandy and Connie put together a great and warming lunch for us all… ummmm, good!!! and much appreciated by all.
Weather is the single factor that will predict our next work session… Winter is here, albeit so far it has been rather mild as far as the snow amount (about 40″ so far), but it can still get bitterly cold in the building… and the building is uninsulated… next up is continuing the electrical, building more saw-horses and sorting out and understanding the wood from the cab, deck, walls and roof… and making drawings of that portion of the Build. Finishing the disassembly to the Trucks… and then cleaning and inspection… will follow.
Background work is ongoing for determining the next steps for the Boiler and Frame. Patterns are nearly ready to go to the foundry for making a couple of replacement parts.
With 2022 here…it is now a new year – Four and a half years since we started on this journey…. Happy New Year everybody!!!! Finally I am caught up on all of my posts from 2021…. stay tuned for what will be coming next at Corry RAILS (check out our new items in our store at our website corryrails.com …MAKE sure you “LIKE” our Facebook page… at the TOP OF THE PAGE and left side under the banner… that will send you notices of when we have a new posting…. also “Like” the post… gives us better numbers to gauge our progress in Social Networking… Thanks!)
In the area around Corry there are a large number of talented machinists and of them there are a few who have extensive knowledge in the workings of vintage steam and gas engines. One such man has been a volunteer helping us analyze the parts and pieces which have been disassembled for many years. Some of those parts have had work done to them and some have not. A couple of parts were missing, but we had enough information and measurement that we could machine new ones.
So in late October we took advantage of a beautiful Fall day to load the engines on to Norm’s flatbed trailer, tie it down, pack up a few totes full of parts and haul it all to our Machinist Friend, and Volunteer, Bill’s shop.
From there the engine will be disassembled and inspected. Bill, with Norm alongside, will be making and acquiring some new parts, making new gaskets and adding new packing and wool-waste for the oiling reservoirs, making sure all clearances are proper, adjusting as necessary… and then final assembly and adjustment will take place.
Since then, much of this has already happened. Bill discovered a few things which indicated that communication between Keith and his machinist wasn’t the best. The work that was done WAS well done… BUT… from the looks of it, the machinist just did what he was told to do and had no input into the project… meaning that the machinist may not have been an “old engine guy” and wasn’t anticipating what Keith was ultimately wanting to have happen… which when final assembly would have begun, some major problems would have reared their collective heads and several things would have had to have been redone. I won’t get into it deeper here, but Bill believes that we have caught all of those issues.
The bores of the cylinders were very straight… very slight taper… cross-hatch honing patterns are still on the cylinder walls right from the Climax factory in 1902, indicating extremely low mileage on the engine and drive-line. There are a few small detail parts that Bill is having made…. just because… and at this point we are waiting for new Piston Rings coming from Niagara Piston Rings, just across the State-line in Clymer, NY… their shop was here in Corry at one time but is now actually located in Panama, NY, just 17 miles away… so, in a few weeks Bill will start the final assembly followed by testing under air…
Come Spring we will bring it back to the shop and it will be here for folks to see as it awaits the reconstruction of the frame and trucks. Stay tuned!!!
Here is a quick update Tom VanTassel and Donnie did for you a week or so ago to give some more perspective on just what we have going on with the restoration as we go into Winter. If you are interested in participating you can contact us through our Facebook page either by a note on a posting or through messenger… or go to our Website at corryrails.com and there are links there as well… or even Email us a corryrails@gmail.com. You can also send us a “Snail Mail” at Corry RAILS, PO Box 313, Corry, PA 16407. We appreciate your support whether it is moral support, actively participating, becoming a Financial Donor and Supporter, or through In-Kind donations of applicable services or supplies ( we can use a lot of different services and suppliers of consumables ) … or even donations of shop equipment and tools. Join in on all of the fun in seeing this project come to life and learn some history in the process.
Just In!!!! We have Christmas ornaments depicting the Climax A and B! They are available in Corry, PA at Hiram’s Marketplace on Center Street, or at the RAILS Gear Store here .
Workdays at the Restoration Building and trips to Alaska have kept progress moving along over the last few months. We have installed shelving, sorted parts, begun the process of refurbishing the engine and located parts that eluded us in the first trip to Alaska in 2020.
Check out these video updates from Fall, 2021
Progress Update with Tom
Corry RAILS Update ~ Dec. 2021…and here is a quick update Tom VanTassel and Donnie did for you a week or so ago to give some more perspective on just what we have going on with the restoration as we go into Winter. If you are interested in participating you can contact us through our Facebook page either by a note on a posting or through messenger… or go to our Website at corryrails.com and there are links there as well… or even Email us a corryrails@gmail.com. You can also send us a “Snail Mail” at Corry RAILS, PO Box 313, Corry, PA 16407. We appreciate your support whether it is moral support, actively participating, becoming a Financial Donor and Supporter or through In-Kind donations of applicable services or supplies ( we can use a lot of different services and suppliers of consumables ) … or even donations of shop equipment and tools. Join in on all of the fun in seeing this project come to life and learn some history in the process.
Fall 2021 Trip to Alaska with Carl and Norm
As you have seen in the previous posts, we covered a lot of territory in Alaska just a few months ago, in the Fall of 2021. One of the primary goals was to get several interviews shot for our upcoming Documentary and at the same time to capture background shots of the area where our engine ran. We had Donnie Rosie fly in for just three days while we ere in Nome and Council just for that. With all of the videos he shot Donnie and his crew created a short update video piece to give our Friends, Fans, Donors and other Team Members a better idea of just what the area where Climax A-313 ran was like. So kick back and enjoy the next 6 minute short video from back in August and early September 2021.
As you have seen in the previous posts, we covered a lot of territory in Alaska just a few months ago, in the Fall of 2021. One of the primary goals was to get several interviews shot for our upcoming Documentary and at the same time to capture background shots of the area where our engine ran. We had Donnie Rosie fly in for just three days while we were in Nome and Council just for that. With all of the videos he shot Donnie and his crew created a short update video piece to give our Friends, Fans, Donors and other Team Members a better idea of just what the area where Climax A-313 ran was like. So kick back and enjoy the next 6 minute short video from back in August and early September 2021.
The next morning (the day after Donnie Rosie headed home to Corry) Norm and I had a couple of more appointments in Nome before we began packing up to catch the 1:00pm flight to Anchorage ourselves.
Later that afternoon we checked into our hotel in downtown Anchorage and found a great Mexican Restaurant just two blocks away for dinner. This part of the trip had originally been scheduled for the beginning of our trip to Alaska …to meet up with Erik Christenson and to be able to spend several days again looking through the various storage units and the log-cabin areas in search of the now-known missing parts. Erik’s work schedule ended up getting flipped which changed everything for us… not the way we really wanted to conduct this trip… but it was important that we do the best we could to accomplish as many of our objectives as we could this year… there was no way for us to maintain our original itinerary.
Erik arrived late that evening from the North Slope and the following morning he had several appointments and wouldn’t be available until that afternoon, so we did a bit of walking around downtown Anchorage that morning. We got to check out the sister engine to the “557” being restored in Wasilla… the “556” has been on display in Merrill Park in downtown Anchorage for many years. the 556 was a sister engine, both being US Army Consolidated engines, type S-160’s, Both engines were shipped to Alaska early in WWII. Of about 2200 of them built, only22 or so exist today. We had a late breakfast at one of the well known eateries in Anchorage, unbeknownst to us, the White Spot Cafe is rated by the periodical “Food & Wine” to have the best sandwich in the State of Alaska. If I had realized that, I might have tried one of their “Fresh caught Halibut Sandwiches” instead of a regular burger… I noticed the sign on the way out the door. Erik picked us up and over the next day and a half we spent time in search of the missing parts.
Not much was found on the first day. A key was missing for one of the locations, which was disappointing…. and we developed nothing new in the Storage unit we were able to get into. We were able to stop by and see Pat Durand at the 557 shop and give him an update on the Nome portion of the trip. It was getting late as we headed back to Anchorage where we were going to grab some dinner… but it seemed that every restaurant we went to had a two-hour wait… we finally ended up back at the Mexican restaurant for a good meal.
The next morning Erik called and he had to spend some time with a contractor getting him situated on a project Erik is involved with. By the time Erik could break loose and pick us up, we headed straight to the next units… not much of anything in the second unit but within minutes of getting into the third unit we did locate several of the most important missing parts. We also found some outstanding photographs we had not seen before.
Erik’s time off this trip was filled with some minor surgery and Dental appointments and several other scheduled annual tests and interviews, so our time in Anchorage was compressed. In fact Erik was scheduled for surgery the next morning. There are still some places we weren’t able to get into that haven’t been searched completely yet… Hopefully Erik will be able to get into them this next Spring. It was getting late and we headed back into Anchorage for a quick meal and then bid adieu… till we meet again.
With the extra parts accumulating from Nome and Anchorage it became a juggling act in making sure our bags weren’t overweight now that we were bringing back about 60lbs of extra parts, pieces and materials. We had rescheduled our flights home, and the next morning we were flying out, headed back to Corry. With the re-booking it put Norm and me in different rows… and of course it was a full flight with our stop over changing from Minneapolis to Chicago, and with barely enough time to make it to our connecting flight to Cleveland. Our good friend and supporter, Tom Grice picked us up in Cleveland and he came fully prepared with water, coffee, soda… whatever we wanted and a assortment of munchies as well…. even bags of popcorn…. Thanks Tom! We arrived home in the very early morning hours of Labor Day…. Thank goodness… it was going to take me most of the day to unpack and do laundry… and then a few days to get my body back on East Coast time.
What a trip… met a bunch more interesting people from all over, including some from right here in Pennsylvania, imagine that!! We learned about some of the ins and outs of the Archive systems in the University Library… found some interesting photos and videos… made some great connections in the Fairbanks area… were able to lay our hands on some original Climax Parts which very few have ever seen… got some important measurements we didn’t have before in order to make templates for some parts… thanks to Donnie we conducted more than a half a dozen taped interviews and gathered more “B” roll for our future Documentary… made some interesting discoveries about some unknown engineering items from Climax not seen before or reported on… met the folks out in the Council area, and I think we are invited back … and spent time familiarizing ourselves with the Ophir and Council mining district… found and saw some Climax items which we never knew existed previously… located about 60# of missing parts… and to top it all off we were given, and brought home, the one and only Climax A-313 Builder Plate. Another successful mission.
As with most investigations, you learn a lot, but a lot of what you learn tends to raise more questions which need to be answered. Will there be another Alaska trip? Quite possibly… we have scratched the surface, and now dig deeper. Funds will have to be raised to make it happen. Anyone who would specifically like to help fund those future searches and investigations and add to the Climax knowledge base, we would love to hear from you… a special one-on-one update as to some of the things we would like to accomplish could be arranged. You can email me at corryrails@gmail.com. That’s the end of the update on the Corry RAILS 2021 Alaska trip.
Now this is one of the highlights of the trip…. one of many, some of which we aren’t talking about yet.. since we are still researching and making connections. BUT, this is what we could say is the “Crown Jewel” of the trip… it made it all worth the effort.
Let’s go back a few years…. January of 2018, right after we were first able to make contact with Erik, to see if there was a way we could bring this locomotive home… after 5 months of attempts… and shortly after we began talking about exactly what was there and where it was stored… what kind of condition… and some photos taken by Keith of parts… Erik made mention that the one thing that his dad did not have was the Builder Plate for A-313.
Beginning in the mid 1890’s, Climax began using the round Climax Builder Plate we are all used to seeing attached to each side of the boiler on the Class B, and later also on the Class C units. On the Class “A” locomotives they only used one Builder Plate, and it was bolted with 4 bolts to the front Running Number Standoff on the Smokebox door on the front of the Boiler. The Builder Plate for this engine had been removed by someone as a trophy well before Chuck Reader hauled Climax A-313 into Nome in the late Fall or early Winter of 1969.
In follow-up conversations with Erik, he thought he recalled his father, Keith, mentioning sometime that the Builder Plate might be on the wall of one of the Bars on Front Street in Nome. Erik had also been to Nome previously, and he thought he recalled that the Bar was the Polaris Hotel & Bar…. located near the end of the Iditerod Dog Sled Race on Front St.
Not long after I had heard this, early in 2018, I discovered that in October of 2017 a fire had destroyed the Polaris with one person perishing… it wasn’t completely burned to the ground, but it was a total loss. My mind raced as I wondered at that time… “Could the Plate have survived?… did someone rescue it?” Bronze can withstand 1700 degrees. Not long after that I found a front-page story in the Nome Nugget, probably published in December… the City Council had voted to knock down the building so that no one could potentially get hurt… the owner was in South Korea receiving medical attention and not available. On the front page was a photo of… Charlie Reader in his Q-Trucking Co. excavator knocking the remains of the building down… how ironic, I thought… here is Charlie Reader, son of Chuck Reader the man who dragged A-313 into town and at onetime an owner of the Polaris Bar, tearing down the building which might have the Builder Plate on the wall… Is that wild???
Well… I would have to wait to see how this plays out… if we can pull this acquisition off… and if I can get to Nome… to see if we can locate the Builder Plate.
Jump forward to the Fall of 2019…. during the Summer we had reached an agreement with Erik and we were planning on being in Anchorage packing up the locomotive parts in August or September. Well, a whole lot of circumstances happened in August which didn’t allow our trip to happen… there were a lot of pieces of the puzzle which had to all align… So, we made the decision to put the Rescue Trip off until June or July of 2020. In the meantime we needed to figure out all of our transportation angles and that was difficult to do here in Corry, PA. At the last minute Tom V. and I made the decision to fly to Anchorage to begin locating equipment and tools we would need for re-packing and to see if we could arrange for the container to be transported to Seattle. Through an introduction made by Pat Durand of the 557 Project, we had dinner shortly after we landed in Anchorage with Jim and Vicki Jansen (another fellow Vietnam Seabee) and Pat Durand. Following dinner and after showing Jim and Vicki photos and info about our Project, Jim offered to transport our container to Seattle on one of his Lynden Transport Barges… OH, My!! We were elated, to say the least. Thank you Jim and Vicki, we are grateful for your generosity… and Pat… for the introductions and all the help along the way.
As part of my planning over the previous year, I had been looking on Facebook to see if there were any Seabees I could make friends with in Nome… I had found that there were a couple… but one in particular just seemed to be the right guy… so I Friended Toby Schield… I had tapped into Toby to see what info there was up there having to do with the old Railroads in general and also the Climax locomotives which had been in Nome during the early 1900’s, all of which were built here in Corry, PA by Climax Manufacturing Co. Although not familiar with that part of Nome’s history, Toby was able to find some good information for me over several months. Toby had been running the Water Dept for a bunch of years and was due to retire in January of 2020, when he would be moving to Nevada, so if we wanted to have Toby’s knowledge available, we needed to make it happen right now, while he and his wife Trish were still in Nome. We really wanted to get up to Nome to see what we could find and see some of the territory where the Wild Goose Railroad operated… and I wanted to meet some of the family of Chuck Reader, who had brought the engine from Ophir and Council to Nome where it sat behind the Q-Trucking building for 10 years before Keith Christenson purchased it. And… oh, yeh!!… then there was always that tantalizing question of “What happened to the Builder’s Plate? … and could we find it.”
A few days before we flew up to Alaska, I called Toby and filled him in on just what Tom V. and I were up to, and that we wanted to come up to Nome for maybe three days to see the town and meet some of the people. A big-hearted Seabee… Toby & Trish offered us a couple of beds at their home… “Come on up!” That was all it took for us to say “Heck, yes!” So, after a wonderful dinner with Pat, Jim and Vicki, we caught a good night’s sleep at out hotel and the next day caught the 11:00am flight to Nome.
On October 16th, 2019, we landed in Nome and Toby was there to greet us and help collect our luggage… and then he introduced us to his wife Trish as she was the Alaska Airlines Ground Crew… the same one who was unloading the baggage and would also be the one refueling the plane for its return flight to Anchorage… It was a very quick “Hello”, “How was the flight”… “Hey, gotta run… see you for dinner!”…. and she was off… what a package of dyn-o-mite! That’s Trish.
We had arrived in Anchorage Tuesday afternoon… then arrived in Nome on Wednesday about noon… were in Nome Thursday, Friday and Saturday… and then flew back to Anchorage with Toby on Sunday. Toby had an annual State Water Board meeting to attend for a few days. In those 4 days in Nome, we covered a lot of territory and met a lot of interesting people… even met Jeff and Peggy Darling who were both from Frewsburg, NY, only 25 miles from Corry… It truly is a small world. I’m going to skip a lot here… suffice to say that we met some great folks… saw and photographed literally tons of stuff we never thought we would ever see and laid the ground work for getting back to Nome in the future. On Friday and Saturday there was an accumulation of about 11″ of snow, the first one of the year, and after an overcast Wednesday and a beautiful, clear and sunny Thursday. Mind you, the temperature never got over 37F.
So, fast forward to Friday morning… Toby, Tom and I hit the road… first stop was Q Trucking to see if Charlie Reader was in… he was not… not surprising, the man gets stuff done!!! …but the word was that we needed to show up about 5pm for the “Weekly Safety Meeting”… and OBTW,, BYOB!!! nothing else needed to be said… we would be there. We made a few more stops around town and then stopped by Hanson’s and grabbed some donuts… and we were off headed out to meet Ron Engstrom… Ron comes from a Pioneer Gold Mining Family and lives out on the Shelton Highway at Basin Creek. The closer we got to Ron’s the lighter the snowfall had been… being only about a one to two inch dusting at Ron’s house. What an incredibly enjoyable few hours we had chatting with Ron…. or rather listening to him chat… and looking at some of his photos…. Ron had the floor. Story’s flew… about his Speeder for getting to school… his propeller driven snow machine… his mom and dad bring in the Dredge with a 60 horse team… dragging the steel bridge in… WOW… we finished up the afternoon walking around in his fields looking at some of the discarded iron… the rusty history of Basin Creek.
Our plan was to come back to Nome the next year after we were done re-packing A-313 in Eagle River , and to spend at least a day on the Dredge with Ron and to interview him for our Documentary. This should have happened in June or July of 2020, except the Covid19 Pandemic got in the way. When travel restriction loosened a bit in July we quickly reinvented our itinerary for getting to Palmer and Eagle River in August of 2020, but we could not travel to Nome because of Covid restrictions… we didn’t have the time to sit in quarantine during the trip. Unfortunately, life is just too short, and you just don’t know what other plans God has for any of us. Ron passed away just a year ago last week, 11-20-2020. But, what memories we have of that afternoon, just a year before.
We said our goodbyes and Tom left Ron with a Corry Rails hat, and we were off to take a tour of the Water Dept facilities in Nome and to checkout one of the Dredges. Then it was time for that “Safety Meeting” appointment… aahemm!! We stopped and picked up a couple of brewskies and made it to the Q-Trucking Shop on-time. We met up with Charlie Reader and several others of the Q-Crew and told them the story of what our plans were for Climax A-313 and enjoyed a couple of cold-ones together. Then, after a bit, Charlie says.. “You really do need to talk to my sister Cussy… she’s the historian in the family!” We had heard that Cussy had been having chemo treatments and that can really drag a person’s energy level down, and Toby asked Charlie if she would be up to it? “I don’t know, let’s find out” Charlie says… and he calls Cussy… tells her about us, and Cussy says “Send ’em over”. So, more goodbyes and by 6:30 we had stopped and picked up Trish and we are at Cussy’s meeting and greeting… For the next couple of hours Cussy holds court and keeps bringing out boxes of stuff… information overload…
I’m sitting on the floor looking over maps and photos and books… We’re kids in a candy-store… trying to absorb as much as we can while listening to the Professor intently. I only wish we had had the foresight to have a video recorder, or at least a tape recorder, going the whole time… what a hoot!!! …sooooo much information in such a short time… I want to do it again… Thanks for the memory Cussy!
Then… I asked Cussy about this rumor I had heard… about the Builder Plate being on the wall of the Polaris Bar… Cussy looks at me and all she said while shaking her head was “You need to talk to Stan Andersen”… and Cussy was instantly on to another subject. Well, Stan Andersen’s name had come up earlier in conversation with Toby… Stan was a Seabee also. Stan had also been on the City Council in Nome and Cussy had worked in the City offices for 34 years… so Toby’s and my eyes met and we nodded to each other with raised eyebrows… as more stories flowed. We finally decided we were all hungry… none of us had had dinner.. so with Cussy all bundled up, it was off to the Pizza place for dinner and a beer…. WHAT an evening… what a day… not a bad day in Nome, even with the snow on the ground. Plans were made that we would all meet-up at the VFW for dinner on Saturday night.
Saturday, Toby, Trish, Tom and I headed out Shelton Highway again, further this time… past Salmon Lake… almost out to Shelton… and pulled into the cabin of Carl Emmons. Another one of the guys who REALLY knows the history and background of a lot that happened in the early days in Nome and with the various iterations of the Railroad…. OH, My!!! more great conversations… and there wasn’t any snow yet that far inland from the Bearing Sea. After a couple of hours with Carl, we headed up the road to check out some flatcars off the side of the road, and then headed back into Nome to make sure we were in line for Dinner at the VFW.
At the Vets Club, we all grabbed a table by the window and Cussy and crew showed up… and Toby and I head to the bar to get a couple of beers. We are at the bar when Toby says “Oh, hey… you need to meet this guy”… I turn around and Toby introduces me to Stan Andersen. Toby takes the beers back to the table leaving Stan and me talking about old times, the Seabees and Vietnam… and what units we were in. Dinner was being served and we made room for Stan at the table as we continued our conversation. I was out of Port Hueneme, CA in MCB-3 at Camp Haskins South in Danang and Stan was out of Gulfport, MS with MCB-133 up at Camp Campbell in Phu Bai, I believe. Neither of us were getting much of our delicious steak dinners eaten… but “It was getting deep, never-the-less”, if ya know what I mean! We eventually transitioned the conversation to our project, the acquisition of Climax A-313, the little engine which had been in Council and Ophir.
Finally I asked Stan about the rumor… and told him that I had asked Cussy, but that she deferred and had only said to “…talk to Stan Andersen…”. Stan takes a sip and says shaking his head, “That plate was never on the wall in the Polaris!” …a long pause, and I’m silent… waiting… and finally he says, “It was on the wall in my Bar… the Bering Sea”… more silence, and then… “but I sold the bar ten years ago or so”. Finally I asked “Did the plate go with the Bar?” to which Stan replies, “No, I kept all the memorabilia on the walls… I’ve got it somewhere, but I haven’t seen it in 5 or 6 years… when I find it, I’ll let you know and see if I can get it to you.” Incredible… Tom is sitting next to me and the look on his face, and probably mine too, had to have been a sight to see… here we are 3500 miles from Corry and we have just found the guy who has THE plate, and possibly we have been offered the Builder Plate we were looking for…. Unreal! Another great day in Nome!
Well, the story gets better as Stan tells the tale about his folks going out camping at Council every year as Stan (and his twin brother Steff, and their sister) was growing up… and on occasion they would drive over to Ophir… about 14 miles away, around the mountain… and one time they spotted this old wooden locomotive (our Climax A-313 of the Wild Goose Railroad, and later the Golovin Bay Railroad – same trackage)… this would have been in the late 1950’s, and they took a couple of photos with the twin brothers hanging on the engine, and with their Dad Steve sitting on the headlight stand in front of the smokestack… and there on the Running Plate is the Builder Plate.
Stan told us that it was then that he said he wanted that Builder Plate for himself… he wasn’t sure if it was that year or the next that he came back and unbolted it. The boys interest in locomotives and trains goes back to when they were 4 or 5 years old, as seen in the photo with their sister on one of the locomotives of “The Last Train to Nowhere”. Later in life, after the military and Vietnam, and returning to Nome and becoming a Bar owner, he placed it on the wall of the Bar where it stayed until he sold the Bar. I think he said that the Bell at the Bar to ring for buying rounds was mounted in front of it… I would like to find a photo or two of it on the wall in the bar, if anyone has one.
Sunday morning, after Toby, Chef Extraordinaire, had prepared an sumptuous Breakfast (Eggs Benedict ala King Crab), we said quick goodbyes to everyone in the area, stopped by the Nome Cemetery to say a quick goodbye and a salute at the gravesite of Chuck Reader, the three of us headed off to the airport to catch our 1:00pm flight. In Anchorage for a few days, we would be making more contacts for the repacking and doing more research, with Toby’s help, when he didn’t have meetings scheduled, before flying home to Corry.
SKIP FORWARD A FEW MONTHS… Out of the Blue, Stan calls me…. “I just wanted to let you know I have found the Plate… I was talking to my brother Steff one day and I mentioned to him that I couldn’t find it…. and Steff says to me ‘What do you mean… I know exactly where it is! After you sold the bar you gave it to me to hang on the wall of our cabin in Council'”. …and then Stan says “I’ll let you know when I have it.”
A few more months go by and I get a note from Cussy and she mentioned that Stan had been in the hospital with some serious issues and had been taken to Anchorage… she asked if Stan had found the Builder Plate, and I filled her in. More back and forth happened over the next several months, and both Stan and Steff were in the hospital at times. When we were planning this trip, and re-planning it at the last minute, to be in Alaska in August, I let Stan know that we were planning to come to Nome and hopefully out to Council at that time. Stan wrote back saying that Steff and Patty, who hadn’t been up in a couple of years, were planning on being in Council also.
That’s all the background…. now, JUMP FORWARD TO THE END OF AUGUST, 2021: The next day, after we arrived in Nome, I sent a Text Message to Stan… Stan’s plan was for the four of us, Stan, Steff, Norm and me to get together the next morning at the VFW. That morning, Norm and I were at the VFW at the appointed time, and waited… and waited… I finally sent a text to Stan asking if he was OK? (since I new that both he and Steff had touch-n-go medical issues)… Stan hadn’t heard from Steff yet that morning, but he would call as soon as he did hear. We left the parking lot and about 20 minutes later Stan called saying that Steff was running behind for check-in for the flight to Anchorage, but could we meet in 15 minutes… SOOOOO ….Stan, Norm and I got together at about 11:00am that Tuesday at the VFW and after hand shakes and introducing Norm, and a bit more chit-chat, Stan reaches in his truck and hands me a bag with the Builder Plate from Climax A-313. WOW!!… it really does exist!! Inside the Club we had a lot more conversation, and some Hats and Shirts… and A-313 Builder Plate Hat Pins, calendars etc. were exchanged …. just can’t get away from those Great days in Nome… when magic happens!!! A replica Builder Plate is in the works to go back on the wall at the Anderson cabin in Council.
Later that afternoon we stopped by Cussy’s, and in the course of conversation she asked if we had talked to Stan yet… and I said we had… and she asks “…and the Plate?” “We have it”, I said. “Where is it?” “Out in the truck”… “Well, Go get it… I want to see it.”… which we gladly did… a fine celebration with a wonderful gal…. Thanks for all your help, history and information Cussy!!!
WELL…. So you see… That’s the reason for pulling this out as a separate topic. Now the Plate is back home and will be used for the time being as a centerpiece in our fundraising efforts until such time as it gets bolted back onto the running plate of the smokebox of A-313. Needless to say, we are pretty proud and grateful to have it in our possession. Thank you so much Stan and Steff!! You have been great caretakers … and everyone else who made it all possible. That made the entire trip worth it, if nothing else were to happen.
Stay tuned for Part IV of the 2021 Alaska Trip…. that will be Catching-up #6.
